Passive Solar Home Design


Passive Solar Home Design

Direct Gain

A photo of a home's interior with sunlight entering through a large window with a view of the mountains.  A table with two chairs sits below the window.This photo shows a mountain home in Colorado that uses passive solar heating, i.e., direct gain.
Photo credit: Dave Parsons

Direct gain is the simplest passive solar home design technique. Sunlight enters the house through the aperture (collector)—usually south-facing windows with a glazing material made of transparent or translucent glass. The sunlight then strikes masonry floors and/or walls, which absorb and store the solar heat. The surfaces of these masonry floors and walls are typically a dark color because dark colors usually absorb more heat than light colors. At night, as the room cools, the heat stored in the thermal mass convects and radiates into the room.

Some builders and homeowners have used water-filled containers located inside the living space to absorb and store solar heat. Water stores twice as much heat as masonry materials per cubic foot of volume. Unlike masonry, water doesn’t support itself. Water thermal storage, therefore, requires carefully designed structural support. Also, water tanks require some minimal maintenance, including periodic (yearly) water treatment to prevent microbial growth.

The amount of passive solar (sometimes called the passive solar fraction) depends on the area of glazing and the amount of thermal mass. The glazing area determines how much solar heat can be collected. And the amount of thermal mass determines how much of that heat can be stored. It is possible to undersize the thermal mass, which results in the house overheating. There is a diminishing return on oversizing thermal mass, but excess mass will not hurt the performance. The ideal ratio of thermal mass to glazing varies by climate.

Another important thing to remember is that the thermal mass must be insulated from the outside temperature. If the thermal mass is not insulated, the collected solar heat can drain away rapidly. Loss of heat is especially likely when the thermal mass is directly connected to the ground or is in contact with outside air at a lower temperature than the desired temperature of the mass.

Even if you simply have a conventional home with south-facing windows without thermal mass, you probably still have some passive solar heating potential (this is often called solar-tempering). To use it to your best advantage, keep windows clean and install window treatments that enhance passive solar heating, reduce nighttime heat loss, and prevent summer overheating.


Indirect Gain (Trombe Walls)

An indirect-gain passive solar home has its thermal storage between the south-facing windows and the living spaces.

An illustration of a cross-section of a passive solar home with a Trombe wall constructed on the south side. It shows how the angle of the winter sun hits the wall, which absorbs the heat and distributes it within the home's interior. It also shows how the angle of the summer sun hits a roof overhang, constructed above the Trombe wall, blocking the sun's heat from entering the home.Download high-resolution diagram:
JPG (ZIP 49 KB) | EPS (ZIP 469 KB)

Using a Trombe wall is the most common indirect-gain approach. The wall consists of an 8–16 inch-thick masonry wall on the south side of a house. A single or double layer of glass is mounted about 1 inch or less in front of the wall’s surface. Solar heat is absorbed by the wall’s dark-colored outside surface and stored in the wall’s mass, where it radiates into the living space.

The Trombe wall distributes or releases heat into the home over a period of several hours. Solar heat migrates through the wall, reaching its rear surface in the late afternoon or early evening. When the indoor temperature falls below that of the wall’s surface, heat begins to radiate and transfer into the room. For example, heat travels through a masonry wall at an average rate of 1 hour per inch. Therefore, the heat absorbed on the outside of an 8-inch-thick concrete wall at noon will enter the interior living space around 8 p.m.


Isolated Gain (Sunspaces)

A photo of a sunspace inside a home. The sunspace features a white brick wall across from the glazing and a grey, ceramic tile floor. Many plants are scattered around the sunspace.This sunspace incorporates masonry thermal mass to store heat for later release when needed.
Photo credit: Donald Aitken.

The most common isolated-gain passive solar home design is a sunspace. A sunspace—also known as a solar room or solarium—can be built as part of a new home or as an addition to an existing one.

The simplest and most reliable sunspace design is to install vertical windows with no overhead glazing. Sunspaces may experience high heat gain and high heat loss through their abundance of glazing. The temperature variations caused by the heat losses and gains can be moderated by thermal mass and low-emissivity windows. For more information, see sunspace orientation and glazing angles.

The thermal masses that can be used include a masonry floor, a masonry wall bordering the house, or water containers. The distribution of heat to the house can be accomplished through ceiling and floor level vents, windows, doors, or fans. Most homeowners and builders also separate the sunspace from the home with doors and/or windows so that home comfort isn’t overly affected by the sunspace’s temperature variations. For more information, see sunspace heat distribution and control.

Sunspaces may often be called and look a lot like “greenhouses.” However, a greenhouse is designed to grow plants while a sunspace is designed to provide heat and aesthetics to a home. Many elements of a greenhouse design that are optimized for growing plants, such as overhead and sloped glazing, are counterproductive to an efficient sunspace. Moisture-related mold and mildew, insects, and dust inherent to gardening in a greenhouse are not especially compatible with a comfortable and healthy living space. Also, it is difficult to shade sloped glass to avoid overheating, while vertical glass can be shaded by a properly sized overhang.


Passive Solar Home Design for Summer Comfort

It makes little sense to save money on winter heating just to spend it on summer cooling. So in most climates, a passive solar home design must provide summer comfort as well. The solar heat in the summer must be blocked by an overhang or other devices, such as awnings, shutters, and trellises.


The physical dimensions of an overhang are an important element because overheating will occur unless the overhang provides enough shade. Many variables—including latitude, climate, solar radiation transmittance, illuminance levels, and window size and type—need to be considered for properly sizing an overhang in a specific locale. Therefore, it’s best to have an experienced solar designer or builder calculate the proper overhang dimensions. For more information, see roof overhangs for shading building elements.




CROATIAN CENTER of RENEWABLE ENERGY SOURCES (CCRES)• was founded in 1988 as the non-profit European Association for Renewable Energy that conducts its work independently of political parties, institutions, commercial enterprises and interest groups, • is dedicated to the cause of completely substituting for nuclear and fossil energy through renewable energy, • regards solar energy supply as essential to preserve the natural resources and a prerequisite for a sustainable economy,• acts to change conventional political priorities and common infrastructures in favor of renewable energy, from the local to the international level, • brings together expertise from the fields of politics, economy, science, and culture to promote the entry of solar energy, • provides the opportunity to play a part in the sociocultural movement for renewable energy by joining the association for everyone, • considers full renewable energy supply a momentous and visionary goal - the challenge of the century to humanity. CCRES Željko Serdar Head of association

Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s